By Wren Calloway Fact-checked by Hugo Lindgren Published
CONFIRMED
GigaDevice has refreshed its GD32H7 family of Cortex-M7 microcontrollers. The new industrial SKUs top out at 750 MHz and 9.5 MB of Flash, and selected parts get an integrated EtherCAT controller. CNX Software, reporting GigaDevice’s announcement, says samples are planned for January 2027 and mass production for April 2027. Pricing has not been announced, and nothing in the reported details mentions a development board for makers yet.
What we know
CNX Software reports that GigaDevice has added industrial SKUs to the GD32H7 Cortex-M7 family and now presents it as one unified high-performance line. The memory ceiling is the headline number. The family now reaches 9728 KB of Flash, which is 9.5 MB, and 1152 KB of SRAM, about 1.125 MB.
That SRAM figure includes 640 KB of tightly coupled memory. Datasheet readers will recognize why this matters. On a Cortex-M7, TCM is the zero-wait-state memory that sits right next to the core. It is where you put your control loop, your interrupt handlers and your hot buffers when the cache cannot give you deterministic timing. 640 KB of it is a generous amount for an MCU.
Not every part runs at 750 MHz, and this is the detail to check before you pick a chip. According to CNX Software, the 750 MHz clock applies only to the GD32H78D, GD32H78E and GD32H789. The GD32H77x parts run at 600 MHz.
The EtherCAT controller is also limited to a few parts. CNX Software says the integrated controller appears only on the GD32H77R and the GD32H78E/77E. The rest of the family does not have it.
The variants are aimed at clear jobs. Per CNX Software, the GD32H77R targets compact robotic joints and servo drives. It adds Ethernet PHYs and motor encoder interfaces next to the EtherCAT block. The GD32H78D/77D goes in a different direction. It targets industrial HMIs and adds a MIPI DSI display interface, graphics acceleration and audio.
On timing, CNX Software reports samples planned for January 2027 and mass production in April 2027. GigaDevice has not announced pricing. Adafruit’s blog relayed the CNX Software article on 2026-11-17, so the news is spreading through maker channels. The underlying facts all trace back to that one report of GigaDevice’s announcement.
What we don’t know yet
Price is the biggest gap. Without per-unit pricing we cannot say whether the 750 MHz parts compete with other high-end Cortex-M7 chips on cost or only on specs.
Development boards are the second gap, and for this site it is the one that matters most. The reported details do not mention an evaluation kit, a Nucleo-style board or anything a hobbyist could order. We are not assuming one exists until GigaDevice or a board maker says so.
The Flash layout is also unclear. GigaDevice’s earlier GD32H7 lineup split memory into 2 MB of executable Flash plus 8 MB of storage Flash. The refreshed family is quoted at 9728 KB total. The reporting does not say whether all of it can execute code directly or whether a similar split still applies. That difference changes how you structure firmware, so check the datasheet once it is out.
We also have no confirmed package options, pin counts, or details about EtherCAT stack licensing and tooling for the new parts. For makers, Arduino core or PlatformIO support is another open question. None of it has been announced.
What it means
This refresh is GigaDevice turning the GD32H7 into a family for industrial motion control and HMI work. For context, GigaDevice already offered EtherCAT in its GD32H75E series, which runs up to 600 MHz with 3840 KB of Flash. The refreshed EtherCAT parts add more memory, and the GD32H78E pairs EtherCAT with the 750 MHz clock.
The company has tried more than one approach to EtherCAT. On 2024-11-11 GigaDevice launched the GDSCN832, a standalone 2/3-port EtherCAT SubDevice controller with two internal PHYs. That chip sits next to a host MCU. The GD32H77R puts the EtherCAT controller, Ethernet PHYs and encoder interfaces on the same die as the Cortex-M7. For a robotic joint board where space is tight, that means fewer chips and less routing.
That is also why the GD32H77R is the most interesting part for robot builders. A servo drive or joint controller needs a fast control loop, encoder inputs and a deterministic fieldbus. On paper, this part covers all three at 600 MHz with TCM for the time-critical code. Treat that as the spec sheet’s promise until real boards and benchmarks show up.
The GD32H78D/77D is the one to watch if you build touch panels or machine front ends. MIPI DSI, graphics acceleration and audio on a Cortex-M7 put it in the range of a capable embedded GUI controller. It does not need a Linux SoC to do that job.
For hobbyists, the honest answer is to wait. Samples arrive in January 2027 at the earliest and volume production follows in April 2027, according to CNX Software. Industrial launches like this often reach engineering teams first and makers later, if at all. Until GigaDevice names a dev board and a price, this is a chip family to bookmark, not one to plan a weekend build around.
When the datasheet lands, check three things first. Look at which part numbers actually get 750 MHz, how the Flash is mapped, and whether a board you can buy for a sensible price exists. We will report on those once GigaDevice confirms them.
Notes on this article
- Fact-checked by Hugo Lindgren before publication.
- Published
Fact-checking
- Every claim is checked by Hugo Lindgren; anything we cannot confirm is corrected, labelled or removed.









