By Wren Calloway Fact-checked by Hugo Lindgren Published
CONFIRMED
ANAVI Technology has opened a Crowd Supply campaign for the ANAVI I2C TPM 2.0, an open-source hardware TPM 2.0 security module for Raspberry Pi boards, CNX Software reports. The board uses Infineon’s Optiga SLB 9673, needs only five pins, and starts at $20. Deliveries are scheduled to begin by March 18, 2027.
What we know
According to CNX Software, citing the Crowd Supply campaign, ANAVI Technology’s new module is a TPM 2.0 board built for Raspberry Pi single-board computers and released as open-source hardware. A TPM (Trusted Platform Module) is a dedicated security chip. It stores keys and handles measurements outside the main SoC, which matters on a board where the whole OS lives on a removable microSD card.
The chip is the Infineon Optiga SLB 9673. CNX Software, citing the ANAVI campaign, says this board is a smaller I2C alternative to ANAVI’s earlier SPI-based TPM 2.0 and that it needs only five pins. ANAVI designed it in response to customer requests.
That pin count is the headline for builders. SPI TPM boards tie up more of the header. A five-pin I2C part leaves more GPIO free for HATs, sensors and whatever else your project hangs off the 40-pin connector.
On the software side, CNX Software reports that the module works with the device tree overlay already included in the official Raspberry Pi Linux kernel. You should not need an out-of-tree driver or a custom kernel build to bring the chip up. The module is compliant with TCG TPM Library specification revision 1.59 and the PC Client Platform TPM Profile version 1.05, per the same report.
Pricing, from the Crowd Supply listing as cited by CNX Software, comes down to two options:
- Horizontal version: $20
- Vertical version: $21
Shipping is $8 in the US and $18 worldwide. Do the math and a single horizontal board lands at $28 in the US or $38 elsewhere. The vertical one comes to $29 or $39. Ordering several boards in one pledge is the obvious way to soften the shipping cost if you are kitting out a small fleet.
Deliveries are scheduled to start by March 18, 2027, per the Crowd Supply listing as reported by CNX Software. That is roughly four months from today.
What we don’t know yet
The CNX Software report does not list which specific Raspberry Pi models the module supports. It describes the board as being for Raspberry Pi boards in general. If you are planning around a particular model, check the campaign page’s compatibility notes before you pledge rather than assuming.
The report also does not cover which Linux userspace tools ANAVI has tested. Spec compliance and in-kernel overlay support are the foundation. A TCG-compliant TPM exposed through the standard kernel driver is what Linux TPM software is built to talk to. Still, we have not seen a confirmed list of tested tools or workflows, so treat specific use cases like disk encryption key sealing or measured boot as something to verify, not a promise.
We also do not have a funding total or backer count. The search results behind this story did not show either figure, so we cannot say how close the campaign is to its goal.
Finally, OSHWA certification is not mentioned for the I2C board. ANAVI calls it open-source hardware. Whether it will carry the same certification as its SPI sibling has not been stated in the reporting we have.
What it means
ANAVI is not new to this. Its earlier SPI-based ANAVI TPM 2.0 for Raspberry Pi was crowdfunded on Crowd Supply in spring 2026. That board uses the Infineon Optiga SLB 9672 and is OSHWA-certified. So the company has already been through one Crowd Supply cycle with a TPM product, and the I2C version is a direct follow-up built from buyer feedback.
The I2C board does not open up the Pi TPM category on its own, either. pi3g’s LetsTrust TPM is an earlier SPI-based board for Raspberry Pi that also uses the Infineon SLB 9672. Its datasheet is dated 2021, and it is sold through retailers such as The Pi Hut rather than crowdfunded. If you need a TPM today and do not want to wait for a campaign, that retail route already exists.
What the ANAVI I2C board brings is the interface. SPI versus I2C is a real trade-off on a crowded header. SPI generally gives more bandwidth, but a TPM is not a throughput device. It signs, seals and stores small amounts of data. Moving it to a five-pin I2C connection is a sensible fit for the job, and it frees up the SPI bus for displays, ADCs or radio modules that actually benefit from the speed.
The horizontal and vertical options matter for enclosure work too. A vertical board can slip into a case that has no room for a flat module. A horizontal one keeps the profile low under a HAT. A $1 difference makes that a mechanical choice, not a budget one.
For anyone building Pi-based gateways, kiosks or remote nodes, a $20 TPM with in-kernel overlay support is a low-friction way to add hardware-backed key storage. The usual crowdfunding caution applies: the March 18, 2027 date is a schedule, not a shipment. ANAVI’s track record with the SPI version is the best signal available right now.
If the board lands on time and the overlay works as described, this could become the default cheap TPM recommendation for Pi projects that are short on pins.
Follow every development in one place on our board release tracker.
Notes on this article
- Fact-checked by Hugo Lindgren before publication.
- Published
Fact-checking
- Every claim is checked by Hugo Lindgren; anything we cannot confirm is corrected, labelled or removed.









