By Samir Haddad Fact-checked by Hugo Lindgren Published
A 16GB Raspberry Pi 5 now lists at $385, more than three times its $120 launch price, yet most of the best Raspberry Pi projects run happily on a $15 Pi Zero 2 W or an old Pi 3 already in your drawer. Below are 21 projects you can build with a Raspberry Pi, sorted by goal. For each one you get the cheapest board that runs it, the extra parts and what they cost in November 2026, how hard it is and the software to install, so you can pick one and finish it this weekend.
Key takeaways
- Pi-hole is the best first project: about an hour of work, almost no extra parts, and you’ll use it every day.
- Most projects need only 2 to 4GB of RAM, so you can reuse a Pi 3 or Pi 4 rather than pay 2026 Pi 5 prices.
- If a project only reads sensors, an ESP32 or Pico is cheaper and uses less power. For heavy server work, a mini PC now costs about the same as a Pi.
- For anything always-on, use the official power supply and an SSD, and flash Raspberry Pi OS Trixie fresh.
- With the AI HAT+ 2 (Hailo-10H, 40 TOPS, 8GB), a Pi 5 can run small generative AI models offline.
Fact-checked
We checked these key facts against the sources named, on November 20, 2026:
- OctoPrint adds a web interface, remote monitoring and timelapses to most USB-connected 3D printers (source: octoprint.org)
- Micron has warned the shortage could last into 2028 or beyond, so don’t count on prices falling soon (source: techrepublic.com)
- Raspberry Pi released Trixie (based on Debian 13) in October 2025 and advises against upgrading a Bookworm installation in place (source: raspberrypi.com)
- An RTL-SDR USB dongle and a 1090 MHz antenna let a Pi decode the position broadcasts from aircraft overhead and plot them on a live map with tar1090 (source: github.com)
- Raspberry Pi had sold over 77 million units by mid-2026, according to its interim results, so almost every problem you hit has already been solved and written up somewhere (source: investegate.co.uk)
Quick picks: the best Raspberry Pi projects by goal
If you have never built anything, start with Pi-hole. It is mostly software and runs on any Pi. Next, try either a weather station, which teaches GPIO wiring, or a retro console, which is easy and fun. The table below sorts every project in this guide by goal, with the cheapest Pi that handles it. Costs cover the extra parts you need beyond the board and a microSD card.
Raspberry Pi projects at a glance (November 2026)
| Project | Goal | Minimum Pi | Approx. extra parts | Difficulty | Build time | Key software |
|---|---|---|---|---|---|---|
| Network-wide ad blocker | Save money, learn networking | Zero 2 W | $0 to $10 | Beginner | 1 hour | Pi-hole |
| Retro gaming console | Fun | Pi 3B+ | $20 to $50 (controllers) | Beginner | 2 hours | RetroPie, Batocera, Recalbox |
| Media centre | Home entertainment | Pi 4 (Pi 3 for 1080p) | $0 to $20 (remote, case) | Beginner | 1 hour | Kodi on LibreELEC |
| Desktop computer | Learn Linux, school | Pi 500+ or Pi 5 4GB | Monitor, mouse | Beginner | 30 minutes | Raspberry Pi OS Trixie |
| Private VPN to home | Security | Zero 2 W | $0 | Beginner | 1 hour | WireGuard, Tailscale |
| Home automation hub | Smart home | Pi 4 (Pi 5 4GB better) | $30 to $60 (SSD, Zigbee dongle) | Intermediate | Half a day | Home Assistant |
| Home NAS | Save money | Pi 4 | Drives plus enclosure | Intermediate | Half a day | OpenMediaVault, Samba |
| Media server | Home entertainment | Pi 4 4GB | Drives | Intermediate | 2 to 3 hours | Jellyfin, Plex |
| Smart mirror or wall dashboard | Smart home | Pi 3B+ | $40 to $150 (monitor, mirror film) | Intermediate | A weekend | MagicMirror² |
| 3D printer control | Making | Pi 3B+ | $0 to $30 (camera) | Intermediate | 2 hours | OctoPrint, Klipper |
| Weather station / air monitor | Learn electronics | Zero 2 W | $10 to $25 (BME280) | Beginner | 2 hours | Python, gpiozero |
| Plant watering / greenhouse | Learn electronics | Zero 2 W | $20 to $40 (ADC, pump, relay) | Intermediate | A weekend | Python |
| Wildlife, timelapse or security cam | Photography, security | Zero 2 W | ~$25 to $35 (Camera Module 3) | Beginner | 2 hours | rpicam-apps, Picamera2 |
| Robot car or rover | Learn robotics | Pi 3 or Zero 2 W | $30 to $60 (chassis, driver) | Intermediate | A weekend | gpiozero |
| Touch drum kit | Music, kids | Pi 3 | $10 to $15 (MPR121) | Beginner | 2 hours | Python, pygame |
| On-device object counter | AI | Any Pi with a camera port | $70 (AI Camera) | Intermediate | Half a day | Picamera2, IMX500 models |
| Offline voice assistant / local LLM | AI | Pi 5 8GB | $200 (AI HAT+ 2) | Advanced | A weekend | Hailo software, Ollama-style servers |
| k3s cluster / homelab | Learn DevOps | 3 x Pi 4 4GB | Switch, PoE HATs | Advanced | A weekend | k3s |
| Web server and dev box | Learn Linux | Pi 4 2GB | $0 | Beginner | 1 to 2 hours | Nginx, Git, VS Code over SSH |
| ADS-B flight tracker | Radio, aviation | Zero 2 W or Pi 3 | $30 to $50 (RTL-SDR, antenna) | Beginner | 2 hours | PiAware, readsb, tar1090 |
| Bug habitat camera | Classroom science | Zero 2 W | ~$27 to $45 (camera, sensor) | Beginner | Half a day | Picamera2 |
Parts costs are rough November 2026 street-price estimates, and US retail prices vary by seller.
Maker tip
Check your drawer before you buy anything. Pi-hole, a VPN, OctoPrint, a weather station and a smart mirror all run on a Pi 3 or a Raspberry Pi 4, so none of them needs a $110 Pi 5.
Before you buy: which Raspberry Pi you actually need in 2026
For a first project, buy the Raspberry Pi 5 4GB at about $110, or reuse any Pi 3 or Pi 4 you already own. You only need 8GB or 16GB for local AI models, heavy containers or desktop multitasking. If a project only reads sensors and switches things on and off, a Pico or ESP32 does the job for a few dollars.
Pi 5 vs Pi 4 vs Pi Zero 2 W vs Pi 500+
Prices have moved five times in a year. These are the current US list prices as reported by Tom’s Hardware, CNX Software, Tech Times and Linuxvox.
| Board | RAM options | Current price (Nov 2026) | Best for | Skip if |
|---|---|---|---|---|
| Raspberry Pi 5 | 2GB, 4GB, 8GB, 16GB | $77.50 / ~$110 / $175 / $385 | Home Assistant, NAS, AI HATs, NVMe storage | Your project only reads a sensor |
| Raspberry Pi 4 | 4GB (other sizes vary) | ~$100 for 4GB | Media centres, retro consoles, reusing older HATs | You need PCIe/NVMe or the AI HAT+ |
| Raspberry Pi Zero 2 W | 512MB | $15 (often out of stock) | Pi-hole, cameras, ADS-B, small sensor nodes | You need a desktop, Docker stacks or USB 3 |
| Raspberry Pi 500+ | 16GB, keyboard form factor | $410 | A complete desktop computer | You want to mount it inside a project |
| Compute Module 5 | 2GB to 16GB | $375 for 16GB | Custom carrier boards, products | It’s your first board |
| Raspberry Pi Pico 2 W | 520KB SRAM (microcontroller) | Under $10 | Sensors, LEDs, simple Wi-Fi gadgets | You need Linux, a screen or a camera |
The Pi 5 is the most capable board here. It has a PCIe lane for NVMe drives and AI accelerators, roughly two to three times the CPU speed of the Pi 4, and two camera/display connectors. The Pi 4 still runs almost every project in this list, but its 4GB model costs nearly as much as a 4GB Pi 5, so only buy a new one if you need its exact form factor. The Zero 2 W is the cheapest Linux board when you can find it, and it’s ideal for single-purpose jobs.
The Pi 500+ is the odd one out. It kept its price in the November round because it was already set at $410 after an earlier rise. That’s a lot for a keyboard computer, but it does come with 16GB of RAM and built-in storage, and those cost $385 on their own if you buy them as a bare Pi 5 16GB.
Why prices jumped (and whether to wait for Pi 6)
The cause is the global memory shortage. AI data centres are buying up DRAM, and LPDDR4 supply is tightening. The Register counted rises in December 2025, February 2026 and April 2026, then two more in late October and on 2 November 2026. The last one added $80 to the 16GB Pi 5. Raspberry Pi calls the increases temporary but has given no date for a cut. Micron has warned the memory squeeze could last into 2028 or later.
Waiting rarely pays off. Tech Times reports the Pi 6 is still about eighteen months away, and it will face the same memory market. The better move is to buy the smallest RAM size that fits the project.
Did you know?
According to Tom’s Hardware, the 16GB Raspberry Pi 5 now costs $385, more than three times its $120 launch price in January 2025. The global memory shortage is to blame.
When a Pico or ESP32 beats a Pi
For projects that only read sensors or toggle outputs, use a microcontroller. Tom’s Hardware reports makers are already moving small projects to Pico and ESP32 boards, and heavier server jobs to mini PCs. Microcontrollers have no SD card to corrupt, boot in under a second and run for weeks on batteries. They also have analog inputs, which the Pi lacks.
| Project type | Raspberry Pi | Pico | ESP32 | Best pick |
|---|---|---|---|---|
| Soil moisture or temperature logging | Works, but needs an external ADC | Good, has ADC, no Wi-Fi on base model | Good, ADC plus Wi-Fi | ESP32 |
| Blinking LEDs, buttons, NeoPixels | Works | Ideal | Ideal | Pico |
| Camera or computer vision | Ideal | Not practical | Basic (ESP32-CAM) | Raspberry Pi |
| Pi-hole, VPN, Home Assistant | Ideal | Not possible | Not possible | Raspberry Pi |
| Battery-powered remote sensor | Poor (high idle draw) | Good | Good, deep sleep | ESP32 |
| Robot with vision or mapping | Ideal | Motor control only | Motor control only | Pi plus a Pico for motors |
You can wire ESP32s and Arduinos the same way you would any general purpose input output project. Many of the sensor ideas below also work as Arduino projects with a few lines changed. At the other end, Tom’s Hardware found that a fully kitted 16GB Pi 5 homelab now costs about the same as an Intel N100 mini PC. If you just want to run many Docker containers, the mini PC gives you more performance per dollar.
The essentials kit: power supply, storage, case, cooling
Every Pi project needs the same four basics, and skimping on any of them is the main reason projects fail:
- Power supply. Use the official 27W USB-C supply (5.1 V, 5 A) for a Pi 5 and the official 15.3W supply (5.1 V, 3 A) for a Pi 4. On a supply that can’t negotiate 5 A, a Pi 5 limits all its USB ports to 600 mA combined, rather than 1.6 A.
- Storage. For projects that are on all the time, use a good-quality A2-rated microSD card or, better, an NVMe SSD on a Pi 5 M.2 HAT or a USB 3 SSD.
- Cooling. Under sustained load the Pi 5 throttles unless it has the Active Cooler or a cooled case.
- Case. A case with GPIO access, so you can add a sensor later without taking it apart.
Power check
The GPIO pins run at 3.3 V logic and can’t take 5 V signals. Never power motors, pumps or LED strips from a GPIO pin: give them their own supply and share only the ground.
Beginner projects (one afternoon, mostly software)
These builds need almost no wiring, so they’re the best fun projects for a new Pi owner. If you just got a Raspberry Pi and are wondering what to do with it, pick one of these. You can finish it in an afternoon and then use it every day.
Network-wide ad blocker with Pi-hole
Pi-hole blocks ads and trackers for every device on your home network, including phones, smart TVs and game consoles, by acting as their DNS server. It runs on any Pi, including a Zero 2 W, and it’s the best first project even if you don’t know networking. You learn as you go: IP addresses, DNS and DHCP reservations.
Spec card: Zero 2 W or any Pi, Raspberry Pi OS Lite (Trixie), wired Ethernet preferred, Pi-hole v6 (which has its own web server), about 1 hour.
Build steps
- Flash Raspberry Pi OS Lite with Raspberry Pi Imager, setting the hostname, user and SSH in the customisation screen.
- Boot the Pi and connect over SSH.
- Reserve a fixed IP for the Pi in your router’s DHCP settings.
- Run the official Pi-hole installer and note the admin password it prints.
- Point your router’s DNS setting at the Pi’s IP address.
- Open the Pi-hole dashboard and watch the queries arrive.
The installer is one command:
curl -sSL https://install.pi-hole.net | bash
Common gotchas: Some routers won’t let you change the DNS server they hand out. If yours is one of them, turn on Pi-hole’s own DHCP server and switch off the router’s. If the Pi goes offline, your whole network loses DNS, so set a secondary Pi-hole or keep a fallback written down. A few streaming apps break when their ad domains are blocked, and allow-listing that one domain fixes it.
Retro gaming console (RetroPie, Batocera, Recalbox)
A Pi 3B+ handles 8-bit and 16-bit consoles and most original PlayStation games. A Pi 4 or 5 adds smoother N64, Dreamcast and PSP emulation. Batocera and Recalbox are ready-to-flash images with Pi 5 support. RetroPie offers the most configuration but has historically lagged on new hardware, so check its current Pi 5 status before you choose it.
Parts: USB or Bluetooth controllers, a case with a fan for the Pi 5, and HDMI. What you learn: flashing images, controller mapping, and file transfer over Samba. Gotcha: the emulators are legal software, but downloading game ROMs you don’t own is copyright infringement in the US. Stick to games you own and have the right to back up, freely licensed homebrew, and officially released free titles.
Media centre with Kodi/LibreELEC
LibreELEC is a small operating system that boots straight into Kodi, which turns a Pi into a living-room media player. The Pi 4 and Pi 5 both decode 4K HEVC, and a Pi 3 is fine for 1080p. HDMI-CEC lets your TV remote control Kodi, so you often don’t need a separate remote.
Gotcha: Kodi plays files from a USB drive or a network share. Third-party streaming add-ons that pull pirated content are where people get into legal and malware trouble, so use official add-ons only.
A real desktop computer with the Pi 500+
The simplest way to build a computer with a Raspberry Pi is the Pi 500+. It’s a Pi 5 inside a mechanical keyboard with 16GB of RAM and built-in storage. Plug in a monitor and mouse and it’s a full Linux desktop that runs Chromium, LibreOffice, Thonny and VS Code. At $410 it costs more than many people expect. A Pi 5 4GB with the official case, supply and an SSD is the cheaper route, and you put it together yourself.
For a family or classroom machine, either option teaches Linux basics without risking the main PC. For a daily work machine at this price, a refurbished laptop is the honest alternative.
Private VPN to your home network (WireGuard/Tailscale)
A VPN on a Pi lets you reach your home network securely from anywhere. That means your Pi-hole, NAS and Home Assistant all work from your phone while you’re away. Tailscale is the easiest route: install it, log in and your devices see each other with no port forwarding. Plain WireGuard is faster to set up than its reputation suggests, but you need to forward a UDP port on your router.
A Zero 2 W or Pi 3 can handle a home internet connection’s worth of VPN traffic for a handful of users. Combine this with Pi-hole on the same board and your phone blocks ads on mobile data too.
Home and smart-home projects
These are the “what do you actually use your Pi for day to day” projects. They run 24/7, so they need a proper power supply and, ideally, an SSD instead of a microSD card. Budget for both before you start.
Home Assistant hub
Home Assistant connects smart lights, plugs, thermostats and sensors from different brands into one local dashboard with automations, and it works without a cloud account. Install Home Assistant OS on a Pi 4 or, better, a Pi 5 with 4GB. Add a Zigbee or Thread USB dongle if you have those kinds of devices.
Can you run Home Assistant off an SD card? Yes, but its database writes constantly, and SD cards wear out under that load, often within a year or two of heavy logging. Boot from an NVMe SSD on a Pi 5 or a USB SSD on a Pi 4 instead. Keep automatic backups turned on and copy them off the Pi.
Gotcha: plug the Zigbee dongle into a USB 2 port on a short extension cable. USB 3 ports and SSDs cause radio interference that shows up as flaky devices.
Home NAS / file server with OpenMediaVault
OpenMediaVault (OMV) turns a Pi into a network drive with a web interface for shares, users and disk health. A Pi 5 is the sensible choice. Its gigabit Ethernet and PCIe give real throughput, and a Pi 4 with a USB 3 drive enclosure works for lighter use. OMV installs on top of Raspberry Pi OS Lite, so check which Raspberry Pi OS release the current OMV version supports before you flash.
Use powered USB enclosures or a dedicated NAS HAT. Two spinning drives pulling power through the Pi’s USB ports is a classic cause of random disconnects. A NAS also isn’t a backup on its own: keep a second copy of anything you can’t replace.
Jellyfin or Plex media server
Jellyfin (free and open source) and Plex (with a paid tier) organise your movie and TV files and stream them to TVs and phones. The catch on a Pi 5 is that it has no hardware video encoder, so transcoding happens on the CPU and struggles with 4K. Set up your client apps to direct play the original file, and a Pi 4 or Pi 5 serves a household without trouble. If you need transcoding for remote viewers on slow links, buy a mini PC with an Intel iGPU instead.
MagicMirror² smart mirror or wall dashboard
MagicMirror² is an open-source dashboard that shows the time, weather, calendar, news and transit times. Put a monitor behind two-way acrylic and it becomes a mirror. It runs on a Pi 3B+ and up. A smart mirror isn’t too hard for a beginner: the software takes an evening, and most of the weekend goes into the frame. If you skip the mirror and hang a monitor or tablet-sized display as a wall dashboard, it becomes a one-evening project.
Edit config/config.js to add modules, and turn on screen blanking at night so the monitor lasts longer. Our guide to how liquid crystal displays work helps you pick a panel with good viewing angles.
3D printer control with OctoPrint or Klipper
OctoPrint adds a web interface, remote monitoring and timelapses to most USB-connected 3D printers. The OctoPi image installs it in one flash. Klipper goes further and moves the motion calculations onto the Pi for faster, smoother prints, usually through MainsailOS or Fluidd. A Pi 3B+ or Pi 4 is plenty. Add a Camera Module 3 for print monitoring.
Maker tip
For sensor-only projects such as plant watering or temperature logging, an ESP32 or Pico costs a fraction of a Pi and uses far less power. Save the Pi for jobs that need Linux, a camera or a screen.
Hardware and GPIO projects (sensors, motors, cameras)
These projects teach real electronics: wiring to the 40-pin header, I2C buses, motor drivers and cameras. Use Python with gpiozero for buttons, LEDs and motors. gpiozero works on the Pi 5’s new RP1 I/O chip through the lgpio backend. Some boards ship without the header fitted, so you may need to solder it on yourself, and a temperature-controlled soldering iron makes that easy.
Weather station / indoor air monitor
A BME280 sensor measures temperature, humidity and air pressure over I2C, and it’s the best first wiring project. It runs on any Pi, including a Zero 2 W. Add an SCD40 for real CO₂ readings or a PMS5003 for particulates if you want an indoor air monitor.
| From (BME280) | To (Raspberry Pi) | Purpose |
|---|---|---|
| VIN | 3.3 V, physical pin 1 | Power (3.3 V only) |
| GND | GND, physical pin 6 | Ground |
| SDA | GPIO2 / SDA, physical pin 3 | I2C data |
| SCL | GPIO3 / SCL, physical pin 5 | I2C clock |
Turn on I2C in the Control Centre or with sudo raspi-config. On Trixie, install Python libraries in a virtual environment:
python3 -m venv --system-site-packages ~/weather
source ~/weather/bin/activate
pip install adafruit-circuitpython-bme280
i2cdetect -y 1
i2cdetect should show the sensor at 0x76 or 0x77. Then log a reading every minute:
import time
import board
from adafruit_bme280 import basic as adafruit_bme280
i2c = board.I2C() # uses GPIO2 (SDA) and GPIO3 (SCL)
sensor = adafruit_bme280.Adafruit_BME280_I2C(i2c, address=0x76)
with open("weather_log.csv", "a") as log:
while True:
line = f"{time.strftime('%Y-%m-%d %H:%M:%S')},{sensor.temperature:.1f},{sensor.humidity:.1f},{sensor.pressure:.1f}"
print(line)
log.write(line + "\n")
log.flush()
time.sleep(60)
Gotcha: a sensor mounted right on top of the Pi reads several degrees high because of the CPU’s heat. Mount it on a short cable, away from the board. An ESP32 does this job cheaper if all you want is the numbers. Choose the Pi when you also want local graphs (Grafana), a display or Home Assistant on the same box.
Automated plant watering or greenhouse
An automated greenhouse uses a soil moisture sensor to switch a small pump through a relay or MOSFET, and can add a temperature-controlled fan. The Pi has no analog inputs, so a capacitive soil sensor needs an ADS1115 ADC on the I2C bus. This is the clearest case where an ESP32 or Pico W is the better buy: both have built-in ADCs, use milliwatts and won’t corrupt a card when the greenhouse power flickers.
If you use a Pi, give the pump its own 5 V or 12 V supply. Drive it through a logic-level MOSFET or relay module with a flyback diode, and keep the electronics in a box away from water. Anything that switches mains-powered heaters or lights should be designed and wired by a qualified electrician.
Wildlife, timelapse or security camera (Camera Module 3)
The Camera Module 3 uses a 12MP Sony IMX708 sensor with autofocus. It comes in standard, wide-angle and NoIR (infrared, for night shots with IR lights) versions, with Raspberry Pi listing the standard and NoIR models at $25 and the wide-angle models at $35. A Zero 2 W handles timelapse and wildlife capture. Use a Pi 4 or 5 if you want motion detection on several streams.
A timelapse is one command with rpicam-apps (formerly libcamera-apps):
rpicam-still --timelapse 60000 -t 3600000 -o frame%04d.jpg
That takes a frame every 60 seconds for an hour. For triggered capture, Picamera2 in Python gives you full control. Gotcha: the Pi 5 and Zero 2 W use the smaller 22-pin camera connector, so you need the right ribbon cable for your board. Point security cameras only at your own property.
Robot car or rover
A robot car is a two-motor chassis, a motor driver such as a DRV8833, a battery pack for the motors and a Pi running gpiozero’s Robot class. A Pi 3 or Zero 2 W is enough to drive it. Choose a Pi 4 or 5 if you plan to add a camera with line-following or object tracking.
from gpiozero import Robot
from time import sleep robot = Robot(left=(17, 18), right=(22, 23))
robot.forward(0.6)
sleep(2)
robot.right(0.5)
sleep(0.5)
robot.stop()
Gotcha: never power the motors from the Pi’s 5 V pin. A stalled motor drops the voltage, the Pi reboots, and the rover drives off on its own. Use a separate battery for the motors and connect only the grounds. Experienced builders often let a Pico handle the motor timing and have the Pi send it commands over USB serial.
Touch-sensitive drum kit from kitchen objects
Wire spoons, bananas or foil pads to an MPR121 capacitive touch board (12 inputs over I2C). A Python script with pygame then plays a drum sample when each pad is touched. It runs on a Pi 3 or later, takes an afternoon, and teaches I2C, events and audio in a way kids remember. Sonic Pi, which comes with Raspberry Pi OS, can play the sounds instead if you want to make it a live-coding lesson.
AI projects on a Raspberry Pi in 2026
AI on a Pi really works now, through three official add-ons. The AI Camera does object detection on any Pi with a camera port. The AI HAT+ speeds up vision on a Pi 5. The AI HAT+ 2 runs small generative models such as chatbots and voice assistants offline on a Pi 5. A Trixie update added built-in support for the Hailo-based AI Kit and AI HAT+, as Hackster reported, so setup no longer needs the hacks it did in 2024.
AI Camera vs AI HAT+ vs AI HAT+ 2
| Add-on | Accelerator | Performance | Compatible Pi | Price | Example project |
|---|---|---|---|---|---|
| Raspberry Pi AI Camera | Sony IMX500 (on-sensor AI) | Runs small vision models on the sensor | Any Pi with a camera connector, including Zero 2 W | $70 | Bird-feeder visitor counter |
| Raspberry Pi AI HAT+ 13 TOPS | Hailo-8L | 13 TOPS | Pi 5 only (PCIe) | $70 | Real-time person detection |
| Raspberry Pi AI HAT+ 26 TOPS | Hailo-8 | 26 TOPS | Pi 5 only (PCIe) | $110 | Multi-camera detection, pose estimation |
| Raspberry Pi AI HAT+ 2 | Hailo-10H with 8GB on-board RAM | 40 TOPS (INT4) | Pi 5 only (PCIe) | $200 (launched at $130) | Offline chatbot or voice assistant |
The AI HAT+ boards are built for vision: detection, segmentation and pose. They can’t run large language models well, because they don’t have the memory. The AI HAT+ 2 fixes that with its own 8GB of RAM. Raspberry Pi’s launch post shows it running small language models of around 1 to 1.5 billion parameters, such as Llama 3.2 and Qwen2.5 variants. These are useful for simple Q&A, summarising and voice commands, but they’re nowhere near ChatGPT.
Did you know?
According to Raspberry Pi’s launch announcement, the AI HAT+ 2 carries its own 8GB of RAM. That means a Pi 5 can run small generative AI models without giving up its own memory.
Build: on-device object counter
Mount an AI Camera at a bird feeder, doorway or driveway and use the pre-installed IMX500 object detection model through Picamera2 to count birds, people or cars. The neural network runs on the camera’s sensor, so even a Zero 2 W can handle it, and no images leave your house. Log counts to a CSV file or send them to Home Assistant over MQTT. If you need higher frame rates or several cameras, the AI HAT+ on a Pi 5 is the step up.
Build: offline voice assistant / local LLM
Use a Pi 5 with 8GB, the AI HAT+ 2, a USB microphone and a speaker. The pipeline is speech-to-text, then a small LLM on the Hailo-10H, then text-to-speech, and nothing goes to the cloud. Expect short, practical answers and a few seconds of delay. It’s a good weekend project if you care about privacy, and it plugs into Home Assistant’s voice features.
The honest counter-argument: a Pi 5 16GB can run the same small models on its CPU with llama.cpp or Ollama, only more slowly. If you already own an 8GB Pi 5, the AI HAT+ 2 is the cheaper way to get usable speed. If you own neither, an older gaming PC with a GPU runs much larger models.
Advanced projects
These are homelab builds for people who already know Linux basics. They teach the skills used in professional IT, but compare the cost with a mini PC first.
k3s/Kubernetes cluster
Three or four Pis running k3s, the lightweight Kubernetes distribution, make a real cluster. On it you can practise deployments, rolling updates and node failures. Pi 4 4GB boards are enough. PoE+ HATs and a PoE switch cut the cables down to one per node, and NVMe or USB SSDs stop etcd from wearing out SD cards.
Cost reality check: four new 4GB Pi 5s plus PoE HATs and a switch cost far more in 2026 than one used mini PC running a few k3s virtual machines. Build the Pi version if you want physical nodes to unplug and a low-power cluster on your desk. Choose the mini PC if you just want to learn Kubernetes.
Self-hosted web server and dev box
A Pi 4 2GB running Nginx can host a personal site, a wiki or a Git server. Put a Cloudflare Tunnel or Tailscale in front of it and you don’t need to open ports. As a dev box, you can SSH in from VS Code’s remote extension and code on the Pi from your laptop. This is the cheapest way to learn Linux administration, and an old Pi 3 is still useful here.
ADS-B flight tracker
An RTL-SDR USB dongle and a 1090 MHz antenna let a Pi decode the position broadcasts from aircraft overhead and plot them on a live map with tar1090. FlightAware’s PiAware image makes setup easy, and it runs on a Zero 2 W or Pi 3. Put the antenna as high as you can with a clear view of the sky: range depends far more on antenna placement than on the Pi.
Projects for classrooms and kids
The best classroom projects are cheap, safe (3.3 V and battery-powered) and tied to a subject. Here are current-hardware versions of the classic ideas: camera-based science, music and coding.
| Project | Subject | Hardware | Age guide |
|---|---|---|---|
| Bug habitat camera | Biology, data | Zero 2 W, Camera Module 3, BME280 | 9+ |
| Touch drum kit | Music, physics | Pi 3+, MPR121, foil | 7+ |
| Weather station | Geography, maths | Any Pi, BME280 | 10+ |
| Scratch games with GPIO | Computer science | Pi 4 or 5, LEDs, buttons | 7+ |
| Python reaction timer | Computer science | Any Pi, LED, button | 11+ |
Bug habitat camera
Put a Camera Module 3 and a BME280 on a terrarium or bug hotel. A Picamera2 script takes a photo every few minutes and logs temperature and humidity with each one. Students then line up the activity in the photos with conditions, which makes a real data-handling exercise. The NoIR camera with an IR LED lets you watch at night without disturbing the insects.
Scratch and Python starter builds
Scratch 3 runs on Raspberry Pi OS and has GPIO blocks, so younger students can light LEDs and read buttons without typing code. Older students can move to Python with gpiozero in Thonny. A reaction-timer game using one LED and one button takes 20 lines of code and teaches inputs, outputs and timing.
Minecraft Pi-style and game coding alternatives
Minecraft: Pi Edition is no longer part of current Raspberry Pi OS releases, so older lesson plans built around it need updating. Pygame Zero is the closest replacement for game coding in class, and Scratch covers younger groups. Both run well on a Pi 4 or Pi 5 desktop or a Pi 500+.
Keep your project running: reliability tips
Most always-on Pi projects that “randomly die” have one of three causes: weak power, a worn-out or corrupted microSD card, or overheating. Fix all three before you start a project, not after.
Why SD cards corrupt and how to prevent it
My SD card keeps getting corrupted, what am I doing wrong? It’s usually power loss during a write, constant small writes from logs or databases, or a cheap card. Here’s how to prevent each:
- Use the official power supply. Undervoltage causes silent write errors.
- Shut down properly instead of pulling the plug:
sudo shutdown -h now
- Move busy projects (Home Assistant, NAS, k3s) to an NVMe SSD on a Pi 5 or a USB SSD on a Pi 4. Both can boot from it directly.
- For appliances that never change, such as a kiosk or dashboard, turn on the read-only overlay file system in
raspi-config. - Make a backup image once the project works.
Random reboots under load: is it my power supply? Almost always, yes. Check with:
vcgencmd get_throttled
throttled=0x0 means no undervoltage or throttling has occurred since boot. Any other value means the power or the cooling needs fixing. Phone chargers that work fine for phones often sag at the currents a Pi 5 draws under load.
Lifespan matters here too. The hardware outlasts the storage by years. Raspberry Pi commits to producing the Pi 5 until at least January 2036. A well-powered, cooled board can easily run a decade. A cheap microSD card under heavy writes can fail in months.
Setting up Raspberry Pi OS Trixie the right way
Should you upgrade from Bookworm to Trixie or reflash? Reflash. Raspberry Pi released Trixie (based on Debian 13) in October 2025 and advises against upgrading a Bookworm installation in place. Trixie brings a new Control Centre that replaces several separate settings tools, a refreshed theme, and 64-bit time handling that fixes the year-2038 problem. Bookworm still gets critical updates, so a working project can stay on it for now.
For a new build, write the image with Raspberry Pi Imager and use its customisation screen to set the hostname, user, Wi-Fi and SSH before first boot. Choose the 64-bit Lite image for headless servers and the desktop image for anything with a screen. A 32-bit image is still available for older boards and software that needs it.
Maker tip
Flash Raspberry Pi OS Trixie fresh with Raspberry Pi Imager instead of upgrading a Bookworm card in place, as Raspberry Pi advises. Keep the old card as a fallback until the new one works.
Where to start this weekend
Pick one project from the beginner list, ideally Pi-hole, and finish it before you buy anything for a second one. Once you’ve finished one, the skills carry over: the SSH and IP setup you learn for Pi-hole is the same setup you’ll use for Home Assistant, a NAS and a k3s cluster. After that, move to a GPIO build like the weather station so you learn the hardware side. The Pi is a popular place to learn these skills: Raspberry Pi had sold over 77 million units by mid-2026, according to its interim results, so almost every problem you hit has already been solved and written up somewhere.
FAQ
What are some things you can use the Raspberry Pi for?
Popular uses include blocking ads across your network with Pi-hole, running a Home Assistant smart-home hub, a retro gaming console, a Kodi media centre or Jellyfin server, a NAS, a smart mirror, a weather station, camera projects, robots, a Linux desktop, and AI projects with the AI Camera or AI HAT+ boards.
Is a Raspberry Pi legal?
Yes. A Raspberry Pi is an ordinary computer and it’s legal to own and use everywhere. As with any computer, legality depends on what you do with it: pointing cameras at neighbours, intercepting other people’s networks or downloading pirated media is illegal whatever the hardware.
What is the lifespan of a Raspberry Pi?
The board itself often lasts 10 years or more with good power and cooling. Raspberry Pi commits to building the Pi 5 until at least January 2036. The weak link is the microSD card, which can wear out in months under heavy writes. Booting from an SSD removes that problem.
How do I build a computer using a Raspberry Pi?
The easiest route is the Pi 500+. Plug in a monitor and mouse and you have a complete Linux desktop. Otherwise, take a Pi 5 4GB or 8GB, add the official 27W supply, a case with cooling, an NVMe SSD or good microSD card, and flash Raspberry Pi OS Trixie with Raspberry Pi Imager.
What is the best first Raspberry Pi project for a beginner?
Pi-hole. It’s mostly software, takes about an hour, runs on any Pi, and teaches networking basics you’ll use in later projects. If you’d rather start with hardware, the BME280 weather station is the best first wiring project.
Which Raspberry Pi should I buy for projects in 2026?
Buy the Raspberry Pi 5 4GB (about $110) for general use. Choose the Zero 2 W ($15) for single jobs like Pi-hole or a camera, a Pi 5 for AI HAT+ 2 projects, and only buy the 16GB model if you’ve confirmed you need the memory. An old Pi 3 or Pi 4 still runs most beginner and smart-home projects.
Why are Raspberry Pi prices so high right now?
There’s a global memory shortage. Demand from AI data centres has pushed up LPDDR4 and LPDDR5 costs, and Raspberry Pi has raised prices five times since December 2025. Micron has warned the shortage could last into 2028 or beyond, so don’t count on prices falling soon.
Is it worth buying a Pi 5 at these prices or should I just get a mini PC?
Buy the Pi if your project needs GPIO, a camera connector, very low power draw or the AI HATs. Buy a mini PC if you mainly want to run Docker containers, Plex transcoding or a homelab. Tom’s Hardware found that kitted-out Pi 5 homelabs now cost about the same as Intel N100 mini PCs, and the mini PCs are faster.
Can a Raspberry Pi run AI or ChatGPT-style models locally?
Small ones, yes. A Pi 5 with the AI HAT+ 2 (Hailo-10H, 40 TOPS, 8GB) runs language models of around 1 to 1.5 billion parameters offline, and a 16GB Pi 5 can run similar models on its CPU more slowly. They handle simple questions and voice commands well, but they’re far below cloud models like ChatGPT.
Should I use a Raspberry Pi or an Arduino/ESP32 for my project?
Use a Raspberry Pi when you need Linux, a screen, a camera, networking services or AI. Use an Arduino, ESP32 or Pico when you’re reading sensors or switching outputs. They’re cheaper, boot instantly, have analog inputs and can run on batteries. Many good builds use both: a Pi as the brain and a microcontroller for real-time control.
Is it legal to use a Raspberry Pi for retro gaming emulation?
Emulators such as those bundled in RetroPie, Batocera and Recalbox are legal software. In the US, downloading ROMs of games you don’t own is copyright infringement. Play games you own and have the right to back up, freely licensed homebrew, or titles publishers have released for free.
Notes on this article
- Fact-checked by Hugo Lindgren against the sources listed below before publication.
- Published
Fact-checking
- Researched from 8 sources, listed below.
- Every claim is checked by Hugo Lindgren; anything we cannot confirm is corrected, labelled or removed.
Sources (8)
- 16GB Raspberry Pi 5 hiked to $385, more than triple its launch price (Tom's Hardware) (tomshardware.com)
- Raspberry Pi hikes prices again barely a month after the last round (The Register) (theregister.com)
- When will this stop? The Raspberry Pi 5 16GB SBC now sells for $385 (CNX Software) (cnx-software.com)
- Raspberry Pi 5 16 GB Hits $385 Following Latest Price Hikes (TechPowerUp) (techpowerup.com)
- Raspberry Pi 16GB models hit by another price hike (PC Guide) (pcguide.com)
- Raspberry Pi cost guide (Linuxvox) (linuxvox.com)
- Raspberry Pi 5 16GB reaches $385, Pi 6 still eighteen months out (Tech Times) (techtimes.com)
- Raspberry Pi and mini PC home lab prices hit parity (Tom's Hardware) (tomshardware.com)









